DIVERSIFIED COATINGS, INC. | 1110 PRODUCT DATA SHEET


					GENERAL INFORMATION Product Description MORWEAR PLUS Advanced Mold Control Paint™ PVA Acrylic High Hiding Wall Primer is for use on interior drywall plaster, concrete, brick, acoustical tile and all types of drywall materials. May be used as a primer coat both before and after texturing. This water base product will provide a uniform base suitable for any type of finish coat and has excellent holdout when used under enamel finish coats. Performance Characteristics Contains an EPA registered mildewcide to protect the paint film only from mildew and mold Seals drywall and plaster Formulated for extra hide Easy to apply Quick drying Soap and Water clean-up Surface Preparation All surfaces must be clean, dry and free from dirt, wax, grease, oil, chalk, mildew and loose or peeling paint. For best adhesion, glossy surfaces should be lightly sanded. Nail holes, cracks or other surface imperfections should be properly filled, sanded smooth and dusted clean. Always wear a dust mask when sanding. All mold, mildew, and fungi must be completely and thoroughly removed. Remove by washing with a commercially available mildew wash. Wear appropriate protective equipment such as rubber gloves, goggles, and other protective clothing when handling mildew wash. Moderate to heavily chalked surfaces require removal of chalk and priming with Advanced Mold Control Paint™ MORWEAR PLUS™ 1110 Interior PVA Acrylic High Hiding Wall Primer. Wallboard and Plaster. When applying to new concrete, plaster or texture-coated surfaces, allow the surface to cure properly. New concrete and plaster must cure a minimum of 30 days. All new interior unpainted drywall and plaster must be primed and sealed with Advanced Mold Control Paint™ MORWEAR PLUS™ 1110 Interior PVA Acrylic High Hiding Wall Primer. Application Suggestions STIR WELL BEFORE USING. May be applied by brush, roller or spray. When spraying, follow spray equipment manufacturer's recommendations carefully. Apply only when the temperature of the surface, material and air is above 50˚F. May be tinted toward finish color with up to 4 fluid ounces of colorant per gallon. DO NOT ALLOW PAINT TO FREEZE. FREEZING MAY REDUCE QUALITY AND THE PERFORMANCE OF THE PAINT. 10 YEAR MOLD PROTECTION: MORWEAR PLUS Advanced Mold Control Paint™ is a high performance paint line that is warranted to resist mold and mildew growth on the paint film only. HEALTH & SAFETY INFORMATION CAUTION! Do not take internally. Use only with adequate ventilation. Avoid breathing vapor, spray mist or sanding dust. Sanding dust may cause eye and skin irritation. Avoid contact with eyes. Avoid prolonged or repeated contact with skin. Close container between use. This product contains chemical(s) known to the State of California to cause cancer and birth defects or other reproductive harm (Prop. 65) KEEP OUT OF REACH OF CHILDREN! Disposal Information Dispose in accordance with all Federal, State and local regulations. Use all of the paint before disposing of the container. If no paint can be poured or drained from the container, dispose of the dry, empty container as you would normal household waste. Store any excess product in a tightly sealed container away from heat or flames. To dispose of a full or partially full container of paint, contact your city or county government for hazardous materials collection locations and operating hours. Do not dispose of excess paint in any sanitary or storm water sewer system. Environmental Considerations. Formulated without lead, mercury or chromium. TECHNICAL INFORMATION - 1110 APPLICATION EQUIPMENT Brush Type: Polyester, Nylon Roller Cover: Quality Synthetic Nap size: 3/8" to 1/2" nap Spray Equipment: Heavy-duty piston 2000 PSI minimum Spray Tip Size: .015 to .019 P.S.I.: 2000 Filter: 60 mesh VISCOSITY: 90-95 KU THINNING: Apply at package consistency. DO NOT THIN. DO NOT USE PAINT THINNER. DRY TIME: Dries in 30 minutes to one hour. Allow 4 hours before applying a finish coat. Drying times will vary depending on surface texture, porosity, temperature and humidity. DESIRED FILM THICKNESS: Wet - 5.6 mils Dry - 1.5 mils COVERAGE: Approximately 250-350 square feet per gallon depending on surface texture and porosity. CLEAN-UP: Clean brushes, rollers and equipment with soap and water. Clean spills and spatters immediately. WEIGHT PER GALLON: 10.86 FLASH POINT: None CONTENT ANALYSIS: Solids by volume: 26.65% Solids by weight: 43.57% Pigment by Weight: 33.26% Vehicle by weight: 66.74% EQUIVALENT FEDERAL SPECIFICATIONS: Meets the performance requirements, not necessarily composition, of Federal Specification: TT-P-650C VOC: Contains less than 100 grams per liter VOC. Revised 1/1/07 Note: To the best of our knowledge, the information contained herein is accurate. However, DIVERSIFIED COATINGS, INC. assumes no liability whatsoever for the accuracy or completeness of the information contained herein. Final determination of the suitability of any information or material for the use contemplated the manner of use and whether there is any infringement of patents is the sole responsibility of the user. Additional information may be obtained through your local sales representative or the Morwear Sales Office.